We can extend the wireless coverage by using 2 more APs to create a wireless repeater:. Please set the wireless mode to ” How can I change to a different wireless network in WinXP? The WLAP is working as a wireless router. But the process failed in the middle. Open your web browser, then type ” How can I create a wireless repeater WDS?

Uploader: Kajijora
Date Added: 25 November 2013
File Size: 21.87 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 21979
Price: Free* [*Free Regsitration Required]

However, it is recommended to keep within air live wt-2000pci users for bandwidth purpose. What is AdHoc and Infrastruture? It might not work for different products. For South American users, please livee the mode to “11b only”. Once you make sure it has emergency code function.

Drivers For Free – Windows 7 bit Drivers

Add Wireless Client Limit Functions. When my AP is installed in an outdoor area with a lot of 2. Please follow the steps below:. By the default, the WAN ping is disabled. So luve AP will not try to air live wt-2000pci between the 2 modes to disrupt the signal connection. Therefore, it is NOT recommend to use.

But the process failed in the middle. To turn it on. The 40bit and 64bit encryption are the same because of out 64 bits, 40 bits are private. There is no access point or wireless router air live wt-2000pci the network.

Theoretically, the Air live wt-2000pci can support the entire subnet of stations users for class C. The value of the wt-200p0ci level in the site survey window ,is it a percentage or dBm? That is why the signal strength is better but the performance is worse. But clients devices can still see air live wt-2000pci other.

WL-5460AP v2

Afterward, please air live wt-2000pci your PC to renew IP address. Cards communicate directly with each other. What can I do? If you use high gain omni antenna and high power setting in near distance, the signal will interfere to each other.

My wireless transfer is very unstable or stopped sometimes. What should I do? The MAC address on the device label is wrong? When activated, the AP will ping the “Watch Host” continuously. What is WEP encryption? Unplug the power of WLAP. Users must select the same key air live wt-2000pci for air live wt-2000pci devices.

Please change air live wt-2000pci wireless channel on your AP or Wireless Router. Please click on “Remote Management” setup button.

Then choose the level1 power again. My PC can’t get on the Internet. After change the TX power setting, please reboot the device to take effect. The South American firmware is for use in South America only, please wt-20000pci not use it in air live wt-2000pci region.

When air live wt-2000pci enable this function, air live wt-2000pci wireless clients will wt-200pci be able to see each other. Therefore, it is an important function for office and Hotspot operator to protect the security between different wireless users.

Hold the reset button while plugging the power. Now Computer A should be able ait connect with Computer B. In the diagram above, Computer B’s distance is too far away from “AP1” to make a wireless connection. How can I change to a different wireless network in WinXP? Then check the remote management, please change the port number to “80”.

It is not recommended to use AdHOC except for small environment. Do not release the reset button until the “Status” LED goes off. The relationship between the percent and dBm are as below: This can be a remote AP, or a local client. WEP adds data encryption to aid single packet transmitted in the wireless air live wt-2000pci. The air live wt-2000pci network are formed by wireless cards only.

You can test this syndrome by pressing “Control-F5” to let the webpage reload when you can access the website. AdHOC and Infrastructure lve 2 ways to form the wireless network.